A microphone dry , singing tired : Reason : Mic IF energy is not enough ; Solution: upgrade 800Hz band ;
2 , Bass Hard : Reason: maximum energy subwoofer too ; Workaround: attenuation of 125-160Hz;
3 , bass scattered : Reason: low-frequency limit can be excessive ; Workaround: Increase the subwoofer lower frequency ;
4 , bass mix : Reason : low center frequency energy is too strong ; Workaround: Attenuation 60-80Hz;
5 , the sound thin, or the sound dry : Reason: low-frequency energy shortage ; Solution: upgrade 250Hz;
6 , the sound hit the ear : Reason: IF too strong ; Workaround: attenuation IK-1.25KHz;
7 , the sound Fried : Reason: the high-frequency energy is too strong ; Workaround: attenuation 2K-4KHz;
8 , raspy voice : Reason: high-frequency energy is too strong ; Workaround : Attenuation 6KHz;
9, the sound has a sense of restlessness : Reason: frequency not submissive ; Workaround: attenuation 8K-1OKHz;
10 , the sound scared : Reason: UHF energy is too strong ; Workaround: attenuation 12K-16KHz;
11 , feeling high, medium and low frequency disjointed : Reason: Crossover frequency attenuation band near excessive ; Solution: upgrade crossover frequency near equilibrium , increasing the degree of integration ;
12 , I feel bad combination of microphones and musical accompaniment : reasons: ① proportion microphone and music right ; ② effect pre-delay parameter is incorrect ; Solution : ① re-adjust the ratio of the microphone and music 6: 4; ② reduce effects pre-delay time ;
13 , feeling subwoofer inflexible : Reason: subwoofer uncoordinated ; Solution: attenuation close to the lower frequency 40Hz or 50Hz, enhance benchmark band 80Hz;
14 , the human voice is not clear enough : Reason: low-frequency too fat ; Workaround: attenuation of 300-500Hz;
15 , vocals impervious : Reason: lack of high frequency ; Solution: mixer frequency sweep to 3K, appropriate to enhance ;
16 , the subwoofer is too soft , weak : Reason: crossover is set too low ; Workaround: Increase the crossover to 120Hz or so, and enhance 100-125Hz frequency band ;
17 , full-range speakers do not feel transparent : Reason: lack of high frequency ; Solution: upgrade 3.5 KHz;
18 , the microphone sound too hard : Reason: the proportion of low-frequency and high-frequency right ; Workaround: attenuation of 500-630Hz, attenuation 1.6K-2.5KHz;
19 , adding reverb microphone , the sound mix ; reasons: excessive low frequency reverberation ; Solution: In the mixer on low frequency reverberation appropriate attenuation ;
20 , ultra-low frequency sound pressure small but resonant sound intensity : Reason : Ultra- low-frequency limit energy is too strong ; Solution: 50Hz substantial attenuation bands below ;
21 , the sound layering bad : Reason: IF too strong ; Solution: Wide Range Attenuation 800-1.6KHz;
22 , high-frequency insufficient sense of space : Reason: Tweeter high frequency characteristic is not good ; Solution: The following overall attenuation IOK to 2KHz band , and then improve the overall gain ;
23 , system pressure limiter , compressor starts to work when the bass becomes scattered ; Cause: Compressor start-up time too fast ; solution: slow down a little pressure limiter start-up time ;
24 , the microphone added incentive processing, sound scared , hair thorn ; reasons: excessive excitation , excitation frequency is high ; Workaround : Reduce the amount of incentives to reduce the excitation frequency ;
25 , after the bass music plus incentive hair mixed feeling hypertrophy ; reasons: excessive excitation , the excitation frequency is low ; Workaround : Reduce the amount of incentives to improve the excitation frequency ;
26 , the microphone sound thin hair flat ; reasons: lack of low-frequency ; Solution: Mixer Equalizer 300Hz sweep around to make enhancements or equalizer boosts 250 ~ 300Hz;
27 , the microphone after adding reverb , decreased sharpness , singing tired ;